How do you join a mining pool from your ASIC firmware?
You join a mining/how-to-choose-bitcoin-mining-pool/">mining pool directly from your ASIC miner’s firmware by entering the pool’s URL, port, and your worker credentials into the miner’s web interface or configuration screen. This process takes about five minutes and requires no additional software on your computer. The specific steps vary slightly depending on the firmware your miner runs - stock manufacturer firmware, Braiins OS, or third-party firmware like Vnish or Hiveon - but the core logic is the same: point your hashrate at a pool’s server instead of mining solo.
Before you start: what you need
You do not need a computer to configure the miner itself, but you do need these things ready:
- Your miner’s IP address, found via your router’s DHCP client list or a network scanner app.
- A mining pool account. Most pools let you create a free account with a username and a worker name (e.g., “YourUsername.Worker1”).
- The pool’s stratum URL and port number. These are listed on the pool’s website or setup page. Common examples:
stratum+tcps://pool.example.com:3333for SSL connections, orstratum+tcp://pool.example.com:3333for plain TCP. - Your miner’s admin password. Stock firmware often uses “root” or “admin” as default; change it after setup.
If you have not chosen a pool yet, our guide “how to choose a bitcoin mining pool for consistent earnings” walks through the trade-offs. This page assumes you already have a pool in mind.
Step 1: access your miner’s web interface
Connect your miner to power and to your local network via Ethernet. Wait 2 - 3 minutes for it to boot. On any device with a web browser (phone, tablet, laptop) that is on the same network, type the miner’s IP address into the address bar. You should see a login page.
- Common default usernames:
root,admin, oruser. - Common default passwords:
root,admin, or leave blank. - If login fails, check the miner’s label or manual for the defaults. If previous owners changed them, you may need to factory reset the miner (usually by holding a reset button or a pinhole for 10 seconds while powered on).
Step 2: Find the Pool Configuration Section
Every firmware puts this in a slightly different place, but the label is almost always one of these:
- Pool Settings or Mining Settings
- Stratum Configuration
- Workers or Pools
- Under a Configuration tab, then a Miner or Pool submenu
On stock Bitmain firmware (Antminer S19, S21 series), it is typically under the Miner Configuration tab. On Braiins OS, it is under Mining then Pools. On Vnish, it is under Settings then Pools.
If you see multiple pool slots (usually 3), you can enter backup pools. The miner will automatically fail over to a backup if the primary pool goes offline.
Step 3: enter your pool details
You will see fields similar to these:
- URL or Stratum URL: Enter the pool’s stratum address exactly as given by the pool. Example:
stratum+tcp://pool.viabtc.com:3333 - Worker or User: Enter your pool username and worker name in the format
Username.WorkerName. Some pools useUsername_WorkerNameor simplyUsername. Check the pool’s documentation. - Password: Most pools ignore this field. You can put anything, or leave it blank. A common practice is to type
xas a placeholder.
Do not include spaces. Do not add extra characters. Copy and paste if possible to avoid typos.
If your pool supports SSL/TLS (look for port numbers like 3334, 443, or addresses beginning with stratum+tcps://), use that for better security. The miner must support SSL for this to work; most modern ASICs do.
Step 4: Save and Apply
Click Save or Apply. The miner will reboot or restart its mining processes. This usually takes 30 - 60 seconds. After restart, the miner should connect to the pool.
Step 5: Verify the Connection
Go back to the miner’s dashboard or status page. Look for:
- Pool or Stratum Status: Should read “Connected” or “Alive”.
- Hashrate: Should show a hashrate close to the miner’s rated spec.
- Accepted Shares: Should start incrementing within a few minutes.
- Rejected Shares: Should be 0% or very low (under 1% is normal). High rejection means wrong pool URL, incorrect worker name, or network issues.
If you see “Disconnected” or “Idle”, double-check the URL and port. If the hashrate shows 0, refer to our guide on “why does your ASIC miner show 0 hashrate after setup”. If shares are rejected, check our article on “why mining pool shares get rejected stale invalid duplicate”.
Firmware-Specific Notes
- Stock Bitmain firmware: Has a simple interface. You can enter up to three pool URLs. The first slot is primary. The miner will try each in order if the previous fails.
- Braiins OS: Offers advanced features like autotuning, but the pool setup is similar. It also supports Stratum V1 and V2. Use the same fields.
- Vnish: Allows separate worker names per pool slot and includes a “test” button to check connectivity without restarting.
- Hiveon OS: Requires you to first create a Hiveon account and add the miner to your farm via the Hiveon web dashboard. Then the pool config is managed from the dashboard, not the miner’s local web interface.
Changing Pools Later
To switch pools, repeat steps 1 through 4 with the new pool’s details. The miner will disconnect from the old pool and reconnect to the new one. There is no cooldown or penalty for switching pools - just lost mining time during the restart.
Common Mistakes
- Using the wrong port number. Double-check the pool’s setup page.
- Entering the pool’s website URL (like
https://pool.example.com) instead of the stratum URL. - Forgetting the worker name part. Some pools require the format
username.workeror they reject shares. - Not saving before leaving the page. The miner keeps running on its previous configuration until you save.
Once connected, your miner will run unattended. Monitor your pool dashboard daily for share rates, hashrate stability, and payout thresholds. Most pools pay automatically when your balance reaches a minimum, typically 0.001 BTC or equivalent.
Not financial advice. taponeth.vip publishes market data and general information about THE AMERICA PARTY. Crypto assets are volatile and you can lose everything you put in. Nothing here is a recommendation to buy, sell or hold, and we make no price predictions.
Prices are sourced from third parties and may be delayed or wrong. Verify anything you intend to act on against a primary source.